Skip to main content

Music Production

LUFS (Loudness Units)

Written as LUFS

Definition

LUFS (loudness units relative to full scale) is the unit of the standard loudness measurement defined in ITU-R BS.1770 and EBU R 128. It is used to compare tracks and programs by loudness and to normalize them.

A peak meter shows how close a signal comes to the top of the scale, but two tracks with the same peak level can sound very different in loudness. A densely compressed song and a gentle piano piece may both peak just below 0 dBFS. A loudness meter estimates what the ear hears instead, and reports it in LUFS: loudness units relative to full scale.

How it is measured

The method is set out in the ITU's Recommendation BS.1770 and in the European Broadcasting Union's R 128 and its meter specification, EBU Tech 3341. In outline:

  1. Each channel passes through K-weighting: a shelving filter that models the acoustic effect of the head, then a high-pass filter.
  2. The meter takes the average power of each channel and adds the channels together. Surround channels count a little more, and the low-frequency effects (LFE) channel is left out.
  3. For a whole program, it measures in overlapping 400-millisecond blocks and ignores the quiet ones, using two gates: one at −70 LUFS, and one 10 LU below the level of the remaining blocks.

The result is the integrated loudness, one number for a whole song or program. Meters also show momentary loudness (a 0.4-second window), short-term loudness (3 seconds) and loudness range (LRA), which describes how much the loudness varies.

LUFS, LKFS and LU

  • LUFS and LKFS are the same unit. The ITU writes LKFS; the EBU uses LUFS.
  • LU is a difference in loudness: 1 LU equals 1 dB. A track at −16 LUFS is 2 LU louder than one at −18 LUFS.
  • Readings are negative because they are measured below digital full scale. A steady 1 kHz sine wave peaking at −23 dBFS in both channels of a stereo file reads −23 LUFS.

Targets

EBU R 128 asks broadcasters to normalize programs to −23 LUFS integrated, with true peaks no higher than −1 dBTP. Music streaming services also turn tracks up or down to a reference loudness when they play, a process called loudness normalization, but each one sets its own reference. Spotify's help pages for artists, for example, say that tracks are adjusted to −14 LUFS, with louder and quieter settings for some listeners. These are company policies, and they change, so check the current specification of each platform rather than treating one number as a rule. Because a louder master is often simply turned down, pushing a master as loud as possible usually gains less than it costs (mastering, dynamics).

A common confusion

LUFS measures average loudness, not peaks. A master can read −14 LUFS and still clip, and one that peaks far below 0 dBFS can still sound loud. Check the true peak too (headroom, clipping), and judge by ear: the meter is a guide to loudness, not to whether the music sounds right.

Common questions

What does LUFS stand for?

Loudness units relative to full scale. It is the unit of the loudness measurement in ITU-R BS.1770 and EBU R 128; the ITU text writes it LKFS (loudness, K-weighted, relative to full scale).

How loud should my master be in LUFS?

There is no single correct number. Broadcast in Europe works to −23 LUFS under EBU R 128; streaming services each normalize to their own reference level, which can change. Follow the delivery specification you are given, leave true-peak headroom, and let the music, not the meter, decide how dense it should be.

What is the difference between LUFS and dBFS?

dBFS describes a signal's level against digital full scale, often its peak. LUFS describes loudness: frequency-weighted, averaged over time and gated to ignore silence. A change of 1 LU equals 1 dB, but the two readings measure different things.

Was this entry helpful?

Comments