
How to Change Guitar Strings (and Keep Your Guitar Playing Well)
A fresh set of strings is one of the cheapest upgrades a guitar gets: D'Addario says regular changes keep the tone, playability and performance of the instrument at their best. Changing them yourself is a skill worth having, and the same afternoon is a good time to wipe the guitar down and check how it is stored. This guide covers when to change strings, how steel and nylon differ, step-by-step restringing for an acoustic, an electric and a classical guitar, how to settle and tune the new set, cleaning, humidity, and when a problem is a job for a technician.
When to change your strings
There is no single schedule. D'Addario, a string maker, says that depending on body chemistry, local weather and taste, some players change strings daily and others once a career, and calls once a month or two "a good bet." Its own signs that it is time: you hear a significant change in the sound, or you see pitting or rust on the strings. Martin Guitar adds that strings that look dirty or sound bad need replacing, and that you should not wait until one breaks.

Look, listen, then use the calendar. The once-a-month-or-two figure is D'Addario's starting point, not a rule.
You can stretch the life of a set. Martin recommends wiping the strings with a soft, dry cloth after playing, which slows the build-up of skin oils and dirt that age strings early.
Steel and nylon: what changes when you restring
Steel strings go on steel-string acoustics and electrics. Nylon strings go on classical (and flamenco) guitars. Martin points out the practical differences: nylon is softer on the fingertips and needs less pressure, while steel tends to hold its tuning better over time, so nylon may need adjusting more often. The attachment also differs. Nylon strings are tied to the bridge; steel strings use bridge pins on an acoustic.

Two families of strings, two ways of attaching them.
One rule is worth repeating. Taylor Guitars says a nylon-string guitar should never be strung with steel strings, because the additional tension will damage the guitar. Martin adds that the swap does not work the other way either: nylon strings on a steel-string guitar give poor sound and playability. Buy the string type your guitar was built for. If you are not sure which you have, look at the bridge and neck: strings tied around a tie block, with no pins, and a wide, flat neck usually mean nylon.
Before you start
You need a new set, wire cutters, a tuner, a soft cloth, and optionally a string winder (it speeds up the winding). D'Addario also suggests resting the neck on a rolled towel and laying a soft cloth or towel under the body so the guitar does not get scratched. Work in a well-lit place, with a stable surface.
Two habits save time. First, loosen the old strings until they are slack, then cut them around the 12th fret, so each half comes off short enough to coil neatly and you do not drag long, sharp ends across the finish. Second, with the strings off, wipe the body, neck and fretboard and look the guitar over: D'Addario suggests checking for loose or damaged frets and worn bridge pins at this point.
Fit the new strings from the thickest to the thinnest. In standard tuning that is E, A, D, G, B, E, strings six to one.

Standard tuning, low to high. Fit and tune in this order. For how these six notes relate and how to tune them, see our guide to tuning your instrument; for other tunings, Drop D and alternate tunings explained.
Choosing replacement strings
Start with the type your guitar was built for: steel or nylon, as above. Taylor notes that changing string gauge (or tuning) alters the tension on the neck, so if you move to a different gauge and the guitar buzzes or feels different, a technician may need to adjust it. If you are unsure which gauge suits your guitar, ask your maker or a technician. Electric guitars differ in how strings load, for example through a tailpiece or through the body from the back, so check your guitar's maker if the bridge looks unfamiliar.
Restringing an acoustic guitar (bridge pins)
The steps below follow D'Addario's acoustic and electric restringing guides.
- Remove the old strings as described above, unwinding each from its tuner post.
- Pull out the bridge pins (a bridge-pin puller, built into many string winders, makes this easy) and keep them in order. Lift the old ball ends out of the bridge.
- Take the thickest string and drop its ball end into the bridge hole.
- Push the matching pin in firmly. While you push down on the pin, gently pull up on the string so the ball end seats snugly. A ball end that is not seated can slip later, and D'Addario notes that causes tuning problems.
- Repeat for each string, thickest to thinnest.

Seating a ball end, drawn as a schematic (not to scale).
Now the headstock. Guide the string to its tuner post and decide how much slack to leave before you wind. D'Addario's trick for modern tuners, where the string passes through a hole in the post, is to hold your palm upright under the string at the 12th fret and use that height to estimate the slack you need. Thread the string through the post, bend it so it wraps under itself, and wind. D'Addario notes that in most cases the string turns away from the logo as you wind, whichever way the tuner is oriented. A couple of wraps is plenty. Do not crank past pitch: D'Addario warns that new strings can break.

Estimate the slack, then wind neatly. Trim the extra only after the string is tuned and settled.
Tune each string as you go, but expect the pitch to drift while the set settles; the "Stretch, tune and settle" section below handles that. Once the strings are up to pitch and holding, trim the tails close to the post with cutters. Cutting last means you never have to guess at the length.
Restringing an electric guitar
The method is the same, with differences in where the string starts. D'Addario's electric guide has you thread each string through its hole in the bridge and make sure the ball end is securely seated, since a loose one can slip and cause tuning problems. It gives the same palm-height slack trick for modern tuners and the same advice to wrap the string under itself.
If your guitar has vintage-style tuners, where the string goes down into a hole in the post, you cannot use the palm test. D'Addario instead says to pull the string slack and cut the excess two tuners past the one you are installing. On a six-in-line headstock like an early Telecaster's, the A string is cut at the G tuner.

On vintage-style tuners, the cut point sits two tuners past the one you are fitting.
On either type, the string should wrap under itself on the post, and a couple of wraps is plenty. This article does not cover tremolo (vibrato) bridges; check your maker's instructions for those.
Restringing a classical guitar (tie-block knot)
Nylon strings tie on, so the bridge is where the new skills are. Taylor Guitars' "Changing Nylon Strings the Taylor Way" is the source for the knot below, and the page has photos of every step. Taylor suggests placing a Post-it note on the top of the guitar behind the bridge so the top is not damaged while you work.
- Slide the end of the string (on the wound bass strings, the loosely wound, more flexible end) through the hole on the front side of the bridge, leaving about three inches (roughly 7.5 cm) sticking out behind it.
- Bring the tail back around and wrap it under the string, making a loop.
- Wrap the tail under the first loop to twist the string around itself, and repeat (once more on the bass strings, twice more on the trebles), so the string twists around itself twice on the basses and three times on the trebles, with the final loop passing below the corner of the back of the bridge.
- Pull tight. The tail now rests along the back of the bridge, long enough to reach just past the next hole. The next string's wraps will pin it in place.
Plain nylon treble strings are slippery; Guitar World's classical guide says to leave plenty of spare tail on them at the bridge.

A highly simplified picture of the tie-block knot. Use Taylor's photographs for the real thing.
At the headstock, pass the other end through the hole in the roller, loop it under the string, and hold a little tension as you pull the loop tight so the bend locks the string in the roller. Wind toward the outside of the rollers, over the tail. Taylor's advice for best tuning is a maximum of four to six wraps; snip the excess when you are done.
Taylor changes strings in order, from the low E, and tucks each tail under the next string. Guide the string so it coils neatly and does not rub the edges of the headstock.
Stretch, tune and settle
New strings go flat as they settle. D'Addario describes the cure: with the guitar tuned, gently pull each string away from the fretboard around the 12th fret. You are not stretching the metal; you are helping the string sit properly at the bridge and the tuner by taking out slack. Retune, play a bit, and retune again until the pitch holds. Be cautious not to pull so hard or fast that the string breaks.

One cycle. Repeat it until the strings hold.
Nylon strings need more patience. Guitar World's guide says the plain nylon strings stretch greatly and the wound bass strings stretch less. Taylor suggests stretching each string gently along its whole length with your thumbs and forefingers, tuning, and repeating the process two or three times. If a nylon string slips at the bridge, redo the knot.
For the tuning itself, a clip-on or phone tuner is fine; How to Tune Your Instrument walks through it, including tuning by ear. To train that ear, Tissimo has two free sheets on beats, the slow pulse you hear when two close notes are not quite in tune. Hear the Pulse Between Two Tones uses steady synthesized tones against 440 Hz to show that the beat rate is the difference between the two frequencies, and that the speed alone does not tell you which side you are on. Tuning Beats: Slower, Faster or the Same? is a listening exercise built on the same idea. Both use pure tones, not a guitar, and the first sheet itself notes that real instruments have harmonics that complicate the pulsing.
Cleaning and everyday care
Martin's maintenance guide gives the routine. Wipe the guitar after every use with a soft cloth, everywhere your skin touched: body, neck, strings and tuners. Polish is optional; the finish is porous, so avoid harsh chemicals and use a little at a time. Fretboards without a finish are raw wood and can dry out; Martin says to condition them a few times a year, depending on humidity. Check your maker's advice first if you are unsure what your fretboard is made of or how it is finished.

Three rhythms of cleaning.
With the strings off you can reach the frets and the fretboard under the strings, which a daily wipe misses.
Humidity and storage
A guitar is mostly wood, and wood takes up and gives off moisture. Both Martin and Taylor give the same target: 45 to 55 percent relative humidity. Martin adds a temperature of 72 to 77°F (about 22 to 25°C), and a hygrometer and thermometer so you can see what your guitar's room is doing. Taylor builds its guitars at about 46 percent humidity and says a digital hygrometer kept in the case is the way to know where you stand.
What the makers say about the extremes: Martin says that if humidity is too low, the wood can dry out and crack or warp; too high, and it swells, which can affect playability and intonation. Humidity can be too high as well as too low, so a hygrometer reading above the band is worth acting on, not only one below it. Taylor lists the signs of a dry guitar as bad string action and buzzing, protruding fret ends, wood cracking, a sinking top and a lifting bridge. Taylor says a case gives essential protection, but in areas prone to severe dryness or cold, such as heated homes, you must use a guitar-humidifying device.

The target band both makers give. The zone labels paraphrase Martin; the edges of the band are not hard thresholds.
Storage is mostly common sense, and Martin's list is a good one: keep the guitar in its case, avoid hot cars and big swings in temperature, never store it in a basement or anywhere water can get in, loosen the strings for a long break, and check on it now and then.

Where your guitar lives matters as much as how you clean it.
When to see a technician
Some problems belong to the person who has the tools. Two words to know, both from Taylor: action is the distance between the strings and the fretboard, and intonation is whether notes stay in tune as you play up the neck. Taylor adds that low action tends to give more accurate intonation, and that intonation on a tempered-scale instrument can never be perfect, so a small amount of error is normal.
Try the simple fixes first. If only one string buzzes, replace that string; Taylor says a kink, or a loose section of the winding around the string's core, can make it buzz or play out of tune. If every string buzzes, try a fresh set. Taylor notes that taking all the strings off at once lets the neck relax, and that a change of string gauge or tuning alters the tension on the neck; either can bring on buzzing that a simple truss-rod adjustment, by a technician, puts right. If buzzing continues or the notes go sour higher on the neck even when the open strings are in tune, a technician can check the action, the neck relief and the intonation, and adjust the truss rod if needed. D'Addario also advises consulting a professional if you find loose or damaged frets or structural damage while you clean.

Fresh strings first, then a technician.
Free worksheets for this lesson
These sheets are about the hearing side of tuning, not the mechanics of restringing:
- Hear the Pulse Between Two Tones — steady tones against 440 Hz at 0, 1 and 3 beats per second, and why speed alone does not tell you sharp from flat
- Tuning Beats: Slower, Faster or the Same? — twelve listening items: compare the beat rate of two clips, judge whether a small move gets closer to 440 Hz, and hear that equal rates can sit on opposite sides
Keep it playing
Restringing gets easy with repetition: slack, wrap, tune, stretch, trim. A tuner tells you when a string is in tune; a teacher tells you what to do about the rest. A Tissimo guitar teacher can watch you restring, check your tuning by ear, and tell you whether a guitar is right for your hands. If you are still choosing an instrument, read Choosing the Right Guitar for Beginners first.
Sources
- How to Restring an Acoustic Guitar — D'Addario
- How to Restring an Electric Guitar — D'Addario
- Changing Nylon Strings the Taylor Way — Taylor Guitars
- On the Bench: Guitar Care Basics with Rob Magargal — Taylor Wood&Steel
- Using a Guitar Humidifier — Taylor Guitars
- Acoustic Guitar Maintenance Guide — Martin Guitar
- Nylon vs. Steel String Acoustic Guitars — Martin Guitar
- Understanding Acoustic Guitar Intonation — Taylor Guitars blog
- Fixing String Buzz — Taylor Guitars
- How to Restring a Classical Guitar — Guitar World
Read this article online: https://tissimo.co/articles/how-to-change-guitar-strings-and-care-for-your-guitar

Comments