Skip to main content
Back
Cover image for the Electric Guitar for Beginners: The Amp, the Pickups and Your First Riffs blog article

Electric Guitar for Beginners: The Amp, the Pickups and Your First Riffs

An electric guitar is two instruments in one: the wood-and-steel part in your hands and the electronic part that turns string motion into sound. Beginners who choose electric often skip the second half and wonder why their first week sounds thin, buzzy or far too loud. This guide covers both halves: how the guitar makes its signal, what the knobs on the amp do, how to practice quietly, and three original riffs that take you from single notes to power chords and palm muting, followed by a four-week plan and a short buying checklist.

How an electric guitar makes sound

An electric guitar relies on its pickups for sound. A magnetic pickup pairs a magnet with a coil of fine copper wire. The magnet creates a steady magnetic field around the steel strings, and when a string vibrates it disturbs that field, which becomes a small electrical signal that travels to the amplifier (StewMac).

Diagram of an electric guitar from above with numbered labels: neck pickup, bridge pickup, pickup selector, volume knob, tone knob and output jack

The parts you control. Real guitars vary in shape, pickup count and where the knobs sit, but most have these six, in some form.

Most beginner guitars have the same few parts to learn:

  • Pickups. Many electrics have one near the neck and one near the bridge. The bridge pickup is typically known as the lead pickup and the neck pickup as the rhythm pickup (Wikipedia).
  • Selector switch. It chooses which pickup or pickups you hear. Flip it while you play one note and listen: that is the fastest way to learn what each position sounds like on your guitar.
  • Volume knob. It sets how much signal leaves the guitar. Turned all the way down, the guitar is silent.
  • Tone knob. Turned down, the sound gets more bassy (StewMac). Most beginners leave it fully up and use it later for a darker tone.

The signal leaves through the output jack. Standard guitar cables use a high-impedance 1/4-inch (6.35 mm) mono plug (Wikipedia).

Single-coil or humbucker

Two pickup types show up on beginner guitars. A single-coil is one coil, and single-coil pickups act like an antenna that is prone to mains hum, a 50 or 60 Hz buzz that depends on where you live (Wikipedia). A humbucker uses two coils, wound opposite to each other and with opposite magnetic polarity. The string signals from the two coils add up, while most of the interference they share cancels. Gibson's Seth Lover designed a humbucking pickup in 1955, and Gibson went on to use it widely, starting with the Les Paul (Wikipedia).

Two panels: a single-coil pickup with one coil, and a humbucker with two coils of opposite polarity, labeled string signals add and most hum cancels

Why a humbucker is quieter: two coils, opposite polarity, wired so that most shared interference cancels. A schematic, not a wiring diagram.

Neither type is better; they sound different. Try both before you decide. If a single-coil guitar hums, remember that a single coil acts like a directional antenna, so the hum can change as you turn or move (Wikipedia).

The amp: gain, EQ and clean versus overdrive

The amp has three jobs: boost the signal, shape the tone and make it loud. Beginners most often confuse two knobs. Gain controls how hard you are driving the amp and alters the tone; master volume controls the overall loudness (London Guitar Academy). Gain is not volume. With the master low and the gain high, you get a distorted sound at a quiet level.

Diagram of the signal chain: strings, pickups, volume and tone knobs, cable, then the amp's gain, bass mid treble, master volume and speaker or headphone jack

The path from pick to speaker. Many amps follow this order, but yours may differ.

Bass, mid and treble are the equalizer: bass controls how many low and deep frequencies come through, and treble adjusts the higher-pitched ones. A clean sound uses little gain, so every note sounds as the guitar made it. An overdrive or distortion sound uses more gain; the more you apply, the more distorted and dirty it gets. Power chords, which you will meet below, are commonly played with distortion or overdrive added (Wikipedia).

Two rows of five amp knobs: clean starting point with low gain, and overdrive starting point with high gain, bass mid treble at noon and master for the room

Two places to start, not rules. Set the master for your room, change one knob at a time, and trim the bass if a high gain setting turns muddy.

A simple order to start with: turn the master almost all the way down, set gain low and bass, mid and treble at noon, then raise the master until the amp is comfortable for the room. Play a single note and move the gain until the sound suits the song, then adjust bass and treble. Change the master last if the overall level has shifted. Most amps also pair a gain (preamp) control with a master volume, so the same two ideas carry over to your amp even if the labels differ (Wikipedia).

Practicing quietly

An amp that sounds good often sounds too loud. Two quiet options exist. A small practice amp is built for home use; 5 to 25 watts is typical, and a headphone jack lets you get a fully amp-treated sound without going through the speaker (Dummies). Some amps also offer a headphone output among their back-panel features (Wikipedia). Small headphone amps that you listen to through headphones are another quiet option; check the specifications of any you consider.

Headphones also reveal mistakes that a loud amp covers. Play clean first with the volume low enough to hear the pick on the string; that is the sound you are really making.

Your first riffs

A riff is a short, repeated musical idea that gives a song its identity. You do not need a song to write one: you need a few notes, a rhythm and a repeat. The three below are original, written in standard tuning (E, A, D, G, B, E from low to high, Wikipedia). Each is shown in both notation and TAB. Guitar music is usually written an octave above where it sounds, which keeps the low notes close to the treble staff; the small 8 under the clef in the figures marks this. One Guitar Phrase, Two Notations shows the same phrase both ways. If TAB is new, start with how to read guitar tabs and the TAB Detective exercise, which asks you to name the note for a string and fret and write missing TAB digits.

Riff 1: single notes

Start with a line on the low strings, where the notes are big and easy to hear. Only four pitches appear: E, G, A and B. They belong to the E minor pentatonic scale, whose five notes are E G A B D; the pentatonic scale explained covers it, and The Pentatonic & Blues Scales shows the major pentatonic and the blues scale in C on a keyboard.

Two bars of eighth notes in 4/4 on the low strings with TAB: E E G E A E G E, then E E G E B A G E

Riff 1: eight eighth notes per bar (⊓ = downstroke, V = upstroke), mostly the open low E string. TAB frets: bar 1 is 0 0 3 0 5 0 3 0 on string 6; bar 2 is 0 0 3 0 on string 6, then 2 and 0 on string 5, then 3 and 0 on string 6.

Pick every note downward at first. When that is steady, try alternating down and up, as the ⊓ (down) and V (up) marks in the figure show; alternate picking and economy picking explains the habit. Play with a metronome at a speed where you never stop: the metronome guide has a method for raising it, and Tempo & the Metronome gives the quick version.

Riff 2: power chords

A power chord has only two different notes, the root and the fifth, and may add an octave of those notes (Wikipedia). It is written with a 5: E5 means E and B. On the shapes below, the fifth sits two frets higher on the next string up from the root. That rule holds for all three shapes in the figure.

Four whole-note chord stacks with TAB: E5 on strings 6 and 5, G5 on strings 6 and 5, A5 on strings 5 and 4, and A5 plus the octave on strings 5, 4 and 3

E5 is frets 0 and 2, G5 is frets 3 and 5, A5 is frets 0 and 2 one string set higher. The last chord adds the octave (fret 2 on string 3); for it, use your third finger across strings 4 and 3. The small numbers are fretting fingers.

For G5, put your first finger on fret 3 of string 6 and your third finger on fret 5 of string 5; for the open E5 and A5, use your first or third finger on fret 2. Once the root is fretted, as in G5, the same two-finger shape slides up the neck to other roots on strings 6 and 5, and one string set higher it gives C5, D5 and so on.

Five whole-note power chords with TAB: G5, A5 and B5 on strings 6 and 5 at frets 3/5, 5/7 and 7/9, then C5 and D5 on strings 5 and 4 at frets 3/5 and 5/7

One fretted shape, five roots. Index finger on the root, ring finger two frets up; the numbers over the notes are fingers.

With the shapes in hand, play the two-bar riff in the next figure. Strum only the strings in each stack, and count aloud.

Two bars of power chord riff: E5 quarter, two E5 eighths, G5 quarter, A5 quarter; then E5 quarter, two E5 eighths, G5 and A5 eighths, E5 quarter

Riff 2, bar 1: E5, E5, E5, G5, A5 on beats 1, 2, the "and" of 2, 3, 4. Bar 2: the same start, then G5 and A5 as eighths on 3 and its "and", then E5.

Palm muting

Palm muting dampens the strings so the notes sound muted. You place the side of your picking hand across the strings, close to the bridge, while you pick; despite the name, the muting is not done with the palm itself. A slight touch gives light muting, and pressing down harder gives heavy muting (Wikipedia). Start with a light touch and adjust until you like the sound. If the notes die completely, ease off the pressure.

Two bars of eight E eighth notes with TAB zeros: bar 1 marked open: let them ring, bar 2 marked P.M. with a dashed line over all eight notes

The same eight notes twice. Bar 1 rings; bar 2 is palm muted. Only the picking hand changes.

Do this with the clean sound first, then add a little gain. Muting becomes much more obvious with distortion, and it can tighten a distorted sound that would otherwise blur.

Riff 3: your first full riff

The last riff joins the two ideas: muted single notes, then chords that ring. This is the structure of many rock riffs: low notes as the pulse, chords as the answer (how to play rock explains the style).

Two bars with TAB: bar 1 has six palm-muted low E eighths, then G and A eighths; bar 2 has A5 and G5 quarters and an E5 half note

Riff 3. Palm mute the six low E eighths, let the G and A ring, then play A5 and G5 as quarters and let E5 ring for two beats.

When it feels easy, change one thing at a time: swap the A for B, move the final chord, double the rhythm in bar 1. The next figure shows two changes: B instead of A in bar 1 and a final A5. A riff you altered yourself is a riff you wrote.

Riff 3 with two changes: bar 1 ends on G and B, palm-muted E eighths before them; bar 2 has A5 and G5 quarters and an A5 half note

Riff 3, varied: the B replaces the A in bar 1, and A5 replaces E5 at the end. The palm mute still covers only the six E eighths.

For bending once you have the basics, string bending and vibrato is the next expressive step. When your teacher has checked your setup and shown you a comfortable bend, Bend Toward a Note lets you match half-step and whole-step bend targets.

Fixing your first sounds

Most first-week problems have a short checklist. Work through it in order before you blame the guitar.

  • No sound. Check that the cable is seated at both ends, the amp is on, the guitar's volume knob is up and the master volume is not at zero. Then try every selector position: on guitars with a volume knob for each pickup, one of them may be turned down.
  • Thin or harsh. Lower the treble on the amp or turn the guitar's tone knob down a little. Too much gain can also make single notes sound fizzy, so try less.
  • Muddy. Too much bass, or too much gain, can blur chords together. Trim the bass first, then try a little less gain. Chords played low on the neck get muddy first.
  • Hum. If you play a single-coil guitar, see the pickup section: move or turn and listen for a change.
  • Too loud. Lower the master, not the gain, unless you also want a cleaner sound.

Change one thing at a time and play the same note each time, so that you know which change caused which result.

How to practice the riffs

A riff is short, so it is tempting to play it fast and sloppy. Resist that. Loop one bar until it is steady, then join the two bars. Say each count aloud ("1, 2, and, 3, 4"), because spoken counting keeps your pick hand honest when the fretting hand is busy. Play at a speed where you can keep the same sound on every pass; speed up in small steps once you can do ten clean repeats in a row. Record yourself once a week: the phone microphone hears what your ears forgive.

A four-week plan

A short session every day usually works better than one long one a week. Split each session into three parts: 3 minutes to tune and warm up (tuning guide), 7 minutes on last week's material (in week 1, spend it on even downstrokes on the open low E string), and 10 minutes on the new skill.

Four columns, one per week: week 1 sound and single notes, week 2 power chords, week 3 palm muting, week 4 your own riff

Each week adds one skill and keeps the earlier one. The session split is 3, 7 and 10 minutes.

  1. Week 1: sound and single notes. Plug in, set a clean tone, and learn Riff 1 slowly with a metronome (Tempo & the Metronome). Read the TAB and say the string and fret before you play (TAB Detective gives you practice).
  2. Week 2: power chords. Learn E5, G5 and A5, then Riff 2. Practice changes on the count, one chord per beat, before adding the rhythm.
  3. Week 3: palm muting. Mute Riff 1 lightly, then play it open and compare. Add a little gain at the end and listen to how the muting changes.
  4. Week 4: your own riff. Play Riff 3, change two notes, then write a new two-bar riff from the notes and chords you know. Record it on your phone and listen back the next day.

If a week is not comfortable, repeat it. Speed follows control, and nothing here is a deadline.

Buying your first electric: what to check

A guitar that is hard to play teaches nothing. You do not need a specific brand, but you do need a guitar that is comfortable, stays in tune and has working electronics. The checklist below works for a shop or a used guitar.

Six checks for a first electric: hold it, check the electronics, look down the neck, tuning holds, budget the whole kit, bring someone

A practical checklist. It is advice, not a rating of any model or brand.

A few details are easy to miss. Plan for an amp or headphone amp, a cable, a tuner, a strap and picks, because the guitar alone is not a complete kit. Ask whether the guitar has had a setup, since a technician can adjust the string height and other settings. And if you can, bring a teacher or a friend who plays: they can hear problems you cannot yet name.

When lessons help

You can learn a lot alone. A teacher helps with things that are hard to notice yourself: a picking hand that tenses up, a palm mute that is too heavy, a chord change that is slower than you think. A Tissimo guitar teacher can watch your hands in a live lesson, check your setup and tone, and give you the next riff when these are easy. You can book a lesson when you want that feedback.

Free worksheets for this lesson

Sources

Read this article online: https://tissimo.co/articles/electric-guitar-for-beginners-amp-pickups-and-first-riffs

Was this useful?
Dislike buttonLike button
Thank you for your feedback imageThanks for your feedback

Comments