Skip to main content
Back
Image for support article Distorted or Crackling Sound in Music Classroom: Clip Protection, Compressor and the Microphone Too Loud Warning

Distorted or Crackling Sound in Music Classroom: Clip Protection, Compressor and the Microphone Too Loud Warning

If the other person says your loud playing crackles or sounds distorted, your microphone level is usually too high. Music Classroom can warn you when your microphone is overloading, and it has two settings that keep loud peaks in check: Clip protection and Compressor.

Where this applies: Clip protection, Compressor, the "Microphone too loud" warning and the "Headphones detected" offer are Music Classroom features. The settings and the warning work on the standard PeerJS connection, which is the default when a session is started. The classroom for booked Tissimo lessons doesn't have them. The Bluetooth microphone note and the iPhone and iPad reminder described below appear in both classrooms.

The "Microphone too loud" warning

The Microphone too loud notice

If your microphone keeps reaching its maximum level, this notice appears: Microphone too loud, "Your microphone is overloading on loud playing, and the other person hears that as distortion. Move the device further from the instrument, or turn its input level down."

This distortion happens in the microphone itself, before the sound reaches the classroom, so no Tissimo setting can remove it. Fix it at your device:

  1. Move your phone, tablet or computer further from the instrument.
  2. If you use an audio interface or an external microphone, turn its input level (gain) down.
  3. Play a loud passage again and ask the other person whether it still crackles.

The warning only checks while the other person is connected and your microphone is on. It appears at most once each time you open the page, and stays until you close it with ×.

Clip protection

Clip protection catches loud peaks before they distort on the way to the other person. On a computer, hover over its name in Settings to read its description: "Holds sudden loud peaks just under the maximum so your audio doesn't distort on the way to the other person. It leaves everything quieter than that untouched. It can't repair distortion that happens in the microphone itself — if loud playing still crackles, move the device further from the instrument."

It is off until you turn it on:

  1. Open Settings: in the room, from the menu in the classroom toolbar, or on the device check before you select Enter classroom.
  2. Settings opens on the Audio tab. Find Clip protection below Using headphones.
  3. Turn on Clip protection. It takes effect right away, without reconnecting your microphone.
Clip protection and Compressor in the Audio tab of Settings

Compressor

Compressor evens out your level. Its description reads: "Gently evens out your level: quiet playing comes up a little and loud playing is held back a little. Turn it off to keep your full dynamic range. Uses clip protection."

  • Turning on Compressor also turns on Clip protection, because the compressor always works together with it.
  • Turning off Clip protection also turns off Compressor. To turn off only the compressor, switch off Compressor and leave Clip protection on.
  • Leave Compressor off when the other person needs to hear exactly how loud and soft you play, for example when you work on dynamics.

Bluetooth microphones

Wireless earbuds and headsets can make both sides sound like a phone call when you also use them as your microphone. If the microphone selected under Audio source looks like a Bluetooth device from its name (for example AirPods), Settings shows this note under it: "Bluetooth microphones lower the sound quality in both directions. For music, keep these on for listening and pick your device's own microphone here."

So keep the earbuds for listening and pick your device's own microphone, or a wired microphone, under Audio source. The note doesn't appear on iPhone or iPad, and because it goes by the device name, it may not appear for every Bluetooth microphone. For switching devices, see Adjusting Classroom Audio and Camera Settings.

Headphones reminders

On iPhone and iPad, the device check shows this reminder: "On iPhone and iPad, music sounds clearest with headphones: put them on, then turn on "Using headphones" in Settings, under Audio. Without headphones leave it off, or the other person will hear an echo." Select Don't show again to stop seeing it.

In Music Classroom, when Music mode is on, Using headphones is off and your device names suggest you're wearing headphones, the classroom offers to turn Using headphones on:

The Headphones detected notice
  • Select Turn on only if you're really wearing headphones, and keep them on for the whole session.
  • Close it with × to leave the setting off, or select Don't show again to stop the offer in this browser.
  • It is only an offer: the classroom never turns Using headphones on by itself, because through speakers the other person would hear an echo.

For what Music mode, Using headphones and Stereo do, see Music Mode: The Best Sound for Your Instrument in the Classroom.

Quick checklist

  • Leave Music mode on (it is on by default) unless you're in a noisy room.
  • Give loud instruments some distance from the microphone, and turn down the gain on any audio interface or external microphone.
  • Turn on Clip protection for loud playing. Add Compressor only if you want a more even level.
  • Use your device's own microphone or a wired one, not a Bluetooth headset.
  • Wear headphones and turn on Using headphones for the clearest sound.
  • If the sound breaks up or drops out rather than crackling on loud notes, check your connection with Classroom Device Diagnostics.

Still hearing distortion? Contact support and tell us what you hear and which device and microphone you use.

Was this useful?

Thank you for your feedback imageThanks for your feedback

Comments